Help & Downloads
Set up your devices, step by step
Setup guides, apps and drivers for the hardware you use with Counta. Free to download, no sign-in needed.
Setup guides
Printers, step by step
Each set-up has a PDF guide with every screen. Here is the short version.
VigorPOS M4201 · 40 × 25 mm barcode labels
Set up the label printer on a Windows PC to print product labels from Products → Print labels. About 10 minutes; the setup guide walks through every screen.
Setup in 4 steps
- 1
Install the driver
Run the driver as administrator → Install printer driver → Port: Other → model TSC TE200 → the USB port "Label PrinterM4201" → name it M4201 Label.
- 2
Set the printing defaults
Printer properties → Advanced → Printing Defaults (not the Preferences button of a print dialog). Use the settings in the Printing Defaults box.
- 3
Clear old per-user settings
In Command Prompt run this once per Windows user (“not found” is fine):
reg delete "HKCU\Printers\DevModePerUser" /v "M4201 Label" /f - 4
Print a test label
Products → printer icon → layout "Thermal roll — 40 × 25 mm" → Print. In the print dialog choose M4201 Label, Margins: None, Scale: Default.
Printing Defaults
- Label size
- 1.575" × 0.984" (40 × 25 mm)
- Media type
- Labels with gaps
- Gap
- 0.079" (2 mm)
- Printing mode
- Direct thermal
- Graphics type
- Standard (not RLE)
- Speed / Darkness
- 3 "/s · 11
Blank labels? Graphics type must be Standard and Printing mode Direct thermal — then do step 3.
Troubleshooting
The most common problems, and how to fix them.
Labels come out blank
The printer doesn't understand the driver's compressed graphics. In Printing Defaults set Graphics type = Standard and Printing mode = Direct thermal, then run the command from step 3 and print again.
My settings don't save
Settings changed with the Preferences button of a print dialog only apply to that one print. Use Printer properties → Advanced → Printing Defaults, then run the step 3 command.
M4201 Label is not in the print dialog
Check the printer is switched on and listed under Settings → Bluetooth & devices → Printers & scanners. If not, install the driver again (step 1).
Prints across two labels, skips labels or is shifted
Check the label size and gap in Printing Defaults, and Margins: None in the print dialog. A small shift can be corrected with "Fine-tune position" in the Print labels window. If labels are still skipped, calibrate the gap sensor (see the printer's manual).
Faint print or unclear logo
Raise Darkness to 12–14 or lower Speed to 2 "/s. For the shop logo, use Logo: Sharp and a bigger Logo size in the Print labels window.
Kitchen stations · auto-print tickets
Send each dish to the right kitchen by product or category. Kitchen screens show the orders; network printers print every new order by themselves. About 15 minutes; the setup guide walks through every screen.
Setup in 5 steps
- 1
Connect the printer
A network (LAN / Wi-Fi) thermal printer on the same network as the print host PC. Hold FEED while switching it on to print its IP address.
- 2
Install Print Bridge
On the always-on print host PC, download PrintBridge.exe and double-click it. It runs in the background and starts with Windows. If Windows warns, choose More info → Run anyway.
- 3
Set up the stations
POS → More → Setting → Kitchen stations & printers, or Administration → Settings → Kitchen Stations. Add one station per kitchen area, choose its type, enter the printer IP, tick its categories or products, then Test print.
- 4
Keep a print host open
On the Print Bridge PC, keep the POS open (Printer → Print kitchen tickets on this PC, on by default with a Network printer), or open the Kitchen page → Printing → tick Print host. Each kitchen screen picks its station in the header.
- 5
Place a test order
Order from the Order kiosk, or from the POS with Send sales to kitchen on. Each printer station prints only its own dishes, and the order card shows a ✓ chip per station.
Where each dish goes
- 1Its product is ticked on a stationThat station
- 2Else, its category is tickedThe category's station
- 3ElseThe default station
- +"Every dish" stationsAlways get the whole order
Station types
- Screen
- Shows on a Kitchen page screen
- Printer only
- Prints every new order by itself
- Screen + printer
- Shows on a screen and prints
Print Bridge and Print host must be on the same Windows PC. Tablets can be kitchen screens, but not the print host.
Troubleshooting
The most common problems, and how to fix them.
Header says “No print host”
Nothing is printing the kitchen tickets. On the PC with Print Bridge, open the POS (Printer → Print kitchen tickets on this PC) or the Kitchen page (Printing → Print host), and keep it open.
Header says “Print bridge down”
Print Bridge isn't running on the print host PC. Double-click PrintBridge.exe and press R to restart it, or install it (step 2).
Test print times out
The IP address is wrong, the printer is off, or it is on a different network. Print the self-test page again and check that the first three numbers of its IP match the PC’s network.
A dish goes to the wrong station
A product ticked on a station beats its category. Check that station's Products list, then its Categories, then the default station at the bottom.
Two paper tickets for the same dishes
A kitchen screen's own auto-print is on as well as a printer station. On that screen: Printing → untick Auto-print on this screen.
I can't find Stations
Stations are set up in POS → More → Setting → Kitchen stations & printers, or in Administration → Settings → Kitchen Stations, not on the Kitchen page. You need the POS Settings permission.
Still stuck?
Send us a photo of the screen on Telegram and we'll walk you through it.